Common Fault and Handling of Edge Sealing Machine

The main functional units of ordinary edge sealing machines are as follows:
Unit name & amp; German imported equipment unit code
Premilling: 111
The corrugated marks, burrs or non-vertical phenomena caused by the cutting saw are modified by double milling cutter to achieve better sealing effect. Make the sealing edge bar and plate closer to the joint, the integrity and beauty of the better. 1. Coating: Through a special structure, the sealing plate and the sealing material are evenly coated on both sides to ensure that the adhesion force is more solid.
Coating: 291
Through the special structure, the sealing plate and the sealing material are evenly coated to ensure that the adhesion force is more solid.
Delivery: 301
Synchronous sideband supply mechanism during continuous workpiece motion
Chaining: 131
Through the precision linear guide rail movement, the fast cutting structure of high frequency high-speed motor is adopted to ensure the smooth and smooth cutting section.
Crude: 141
Automatic tracking and high frequency high-speed motor structure are adopted to ensure the smooth and smooth of the upper and lower parts of the trim plate. Used for repairing the excess edge material above and below the plate seal bar. The rough knife is a flat knife. The finishing of excess parts in order to process the bark. Because when sealing the wood skin, it is not possible to directly use the finishing knife R-shaped knife. The wooden skin is generally 0.4 mm thick. If the finishing knife is used directly, it is easy to cause fractures. In addition, rough repairs can also be used to seal the first repair process of PVC and acrylic.
Specialization: 142
The finishing knife is an R-shaped knife. It is mainly used for PVC and Acrylic sealing edge strips for plate furniture, and it is better to cover the edge strips with a thickness of 0.8 mm or more.
Scratch: 241
It is used to eliminate the corrugation caused by the cutting process of the trim edge, so that the upper and lower parts of the plate are more smooth and tidy.
Polishing: 151/242
Clean the finished plate with a cotton polishing wheel, and smooth the end surface of the seal through polishing.
Slot opening: 112/113 is mainly used for plate furniture and wood door production.
Used for the closet side plate, bottom plate and other direct slot, reduce the cutting board saw process is more convenient and faster; It can also be used to slot the aluminum edge of the door plate.
Common Fault and Handling of Edge Sealing Machine
The woodworking machine sealing machine and continuous work in high temperature environment are prone to failure, which affects the utilization rate of equipment. If the equipment operator mistakenly repairs the sealing machine and precision cutting saw for mechanical operation under unknown circumstances, scientific maintenance and repair should be used before non-substantive electrical faults can be eliminated to ensure the normal operation of carpentry machinery.

　4 In order to improve the quality of the product, the following points are proposed in response to some problems that have arisen in the sealing machine:
1). Before the guide rail is installed, check whether the guide rail is flat, and the ends of the guide rail should be aligned and quenched.
2). Machine processing for external processing parts, if not processed in accordance with the drawings will be returned, and let foreign manufacturers responsible for certain losses. For the parts processed in the factory, if they are not processed according to the drawings, the person responsible for the installation has the right to return them and reprocess them. For those who can not be processed again, the parties shall pay compensation for the entire material expenses and labor expenses.
3). Bearing for the rubber pot part and pulley part will be all imported bearings, careful not to mix, bearings must be installed in accordance with the installation process.
4). Do not hit hard when the conveyor belt motor is installed! Otherwise it will break the device in the reducer.
5). Whether the chain is transmission chain or transmission chain, do not be too tight or loose!
5 After the premilling cutter, the workpiece is not straight or the end surface is broken:
• The front and rear milling cutter is not aligned
• The line point parameter is not set correctly, at least one knife has not been cut, causing the edge to collapse
• The milling cutter is injured or too blunt, causing the edge to collapse
Importance of maintenance of sealing machine
The use of sealing machine-woodworking machinery equipment, such as careful care of equipment, not only can speed up the progress of the project and reduce maintenance costs. Do not appear heavy use light maintenance phenomenon, the correct use and maintenance of the construction machinery can be summarized as: reduce the load, pay attention to inspection, strengthen lubrication. As long as we pay attention to the maintenance and maintenance of the construction machinery as required, it will reduce the occurrence of early faults, extend the service life, improve the efficiency of the operation, and make the woodworking machinery bring more benefits to you.
1. Do not affect safety or driving due to mechanical accidents during use.
2. The technical status of mechanical assemblies, zeros, and components is balanced to achieve the longest overhaul interval.
3. Keep the machine in good condition and can start operation or exit at any time.
4. Under reasonable conditions, it will not be stopped due to damage in the middle.
Important tips:
• Do not turn on the control power during computer startup!
• Do not shake the keyboard bracket during computer startup!
• Machines and computers are not allowed to turn off power suddenly during work!
• The computer must be shut down according to normal procedures!